Loading...
Viessmann · EN 12828
Technical Datasheet & 2D Drawing (B1HC232)
Dimensional & hydraulic connection schematic
Viessmann Vitodens 100-W, montavimo dalys, kamino atvamzdis Ø60/100 (6,5-26) – Viessmann Katilai serija inžinerinis komponentas, skirtas kategorijai „Katilai ir
Material / Spec: Lakštinis plienas S235JR (3–4 mm), išbandytas 1,5×PN hidrauliniu slėgiu
Akumuliacinėms talpoms – juodas plienas; ŠV boileriams – titano emalis + 850 °C degimas.
EN 12828 sauga: tarp boilerio / akumuliacinės talpos ir apsauginio vožtuvo (3 bar šildymui / 6 bar geriamam vandeniui) bei Statico plėtimosi indo draudžiama montuoti uždaromąją armatūrą.
All [01–06] sub-assemblies, adapters, and gaskets stocked at Eigulių St. 21, Kaunas warehouse (10+ yr service support).
Vytautas engineering compatibility note (B1HC232)
Verified mating components for Viessmann (B1HC232) matched by connection standard (DN / thread / M30×1.5 / RA Click) and hydraulic compatibility.
Yes, this Viessmann unit (SKU B1HC232, category: Boilers & boiler room equipment) is manufactured to European EN 12828 hydronic standards. Verify the connection thread or nominal size (e.g. DN15 1/2", DN20 3/4", M30×1.5 or Danfoss RA Click) – our engineering advisor Vytautas lists directly compatible mating components on this page.
Genuine Viessmann components use corrosion-resistant alloys (DZR brass, bronze or stainless steel) and calibrated flow paths, preventing valve sticking, water-hammer noise and premature seal leaks over 10+ heating seasons.
When installing Viessmann Vitodens 100-W, montavimo dalys, kamino atvamzdis Ø60/100 (6,5-26) (B1HC232, retail price 0,00 €), check whether you need matching union tailpieces, Eurocone adapters, a mating thermostatic head or actuator. See the compatible parts section above.
Always observe the flow-direction arrow on the housing, depressurise the loop before fitting, and never apply hemp or tape onto flat union gaskets or O-ring cones.
Viessmann Viessmann Vitodens 100-W, montavimo dalys, kamino atvamzdis Ø60/100 (6,5-26) (B1HC232) – patikrinkite jungties sriegį ir sistemos parametrus prieš montavimą.
Suderinamumą pasitikslinkite su mūsų inžinieriumi (+370 611 19158) arba pagal įrenginio techninį pasą
Source: Manufacturer technical catalog (Danfoss / IMI Hydronic / HERZ / Haier / Gorenje 2025–2026) and LST EN 215 / EN 12828 / EN 303-5 standard
Verification note: Solid-fuel boiler door aperture and flange dimensions vary by production year and kW rating – before ordering a door conversion kit or pellet burner, verify exact dimensions against the boiler passport or with a „Gilės inžinerija“ engineer (+370 611 19158).
Confirm that B1HC232 connection matches the supply/return pipework and flow direction arrow.
Depressurise the heating circuit, fit the union tailpiece and tighten to factory torque.
Adjust the flow scale (Kvs / l/h) or controller setting according to room or boiler loop load.
Refill the loop, vent trapped air and verify leak-free operation under operating temperature.
Engineer pro tip: When installing Viessmann (B1HC232), never wind hemp onto flat gasket seats or Eurocone O-ring cones – seal only tapered pipe threads.
Pramoninis plieninis Solid fuel boiler 150 kW (angliai up to 180 kW) su orapūte ir valdikliu (KaTRI3850150)
