Loading...
Watts · EN 12828Montavimo ir prijungimo mazgo eiga (2020107):
Gamyklinė komplektacija ir sertifikavimas:
Technical Datasheet & 2D Drawing (2020107)
Dimensional & hydraulic connection schematic
Modelis Watts 2020107 (EAN-13: 4051394000066) (Watts HKV510,7 OUTLET HEAT.CIRC. MANIFOLD COD. IMPEGNATO DA EXPORT CATALOGUE)…
In stock · delivery 1–3 bus. days
Material / Spec: Nerūdijančio plieno AISI 304 arba žalvario G 1" sija su skaidriais 0–5 l/min rotametrais
Srautas l/min reguliuojamas sukant rotametro žiedą, kol plūdė pasiekia projektinę vertę.
EN 1264 balansavimas: vieno 16×2,0 mm kontūro ilgis L ≤ 80–100 m (ΔT = 5 K), srautas nustatomas rotametru (0,5–3,5 l/min) pagal kilpos ilgį.
All [01–06] sub-assemblies, adapters, and gaskets stocked at Eigulių St. 21, Kaunas warehouse (10+ yr service support).
Vytautas engineering compatibility note (2020107)
Verified mating components for Watts (2020107) matched by connection standard (DN / thread / M30×1.5 / RA Click) and hydraulic compatibility.
Yes, this Watts unit (SKU 2020107, category: Underfloor heating & manifolds) is manufactured to European EN 12828 hydronic standards. Verify the connection thread or nominal size (e.g. DN15 1/2", DN20 3/4", M30×1.5 or Danfoss RA Click) – our engineering advisor Vytautas lists directly compatible mating components on this page.
Genuine Watts components use corrosion-resistant alloys (DZR brass, bronze or stainless steel) and calibrated flow paths, preventing valve sticking, water-hammer noise and premature seal leaks over 10+ heating seasons.
When installing Watts HKV510,7 OUTLET HEAT.CIRC. MANIFOLD COD. IMPEGNATO DA EXPORT CATALOGUE (2020107, retail price 297,51 €), check whether you need matching union tailpieces, Eurocone adapters, a mating thermostatic head or actuator. See the compatible parts section above.
Always observe the flow-direction arrow on the housing, depressurise the loop before fitting, and never apply hemp or tape onto flat union gaskets or O-ring cones.
Dynacon stainless steel underfloor heating manifold with automatic balancing & control valves (11 loops G3/4″) includes air vent, drain valve, brackets, connection 1″ – 9330-11.800
Dynacon stainless steel underfloor heating manifold with automatic balancing & control valves (10 loops G3/4″) includes air vent, drain valve, brackets, connection 1″ – 9330-10.800
Kolektoriaus kontūrų atvamzdžiai yra G 3/4" Eurokonus (reikia po 2 vnt. Eurokonus jungčių kiekvienam vamzdžio žiedui), o pavarų sriegis – standartinis M30×1,5 (tinka EMO T 1807-00.500 ir Danfoss TWA-K M30×1,5 pavaros).
Suderinamumą pasitikslinkite su mūsų inžinieriumi (+370 693 97098) arba pagal įrenginio techninį pasą
Source: Manufacturer technical catalog (Danfoss / IMI Hydronic / HERZ / Haier / Gorenje 2025–2026) and LST EN 215 / EN 12828 / EN 303-5 standard
Verification note: Solid-fuel boiler door aperture and flange dimensions vary by production year and kW rating – before ordering a door conversion kit or pellet burner, verify exact dimensions against the boiler passport or with a „Gilės inžinerija“ engineer (+370 693 97098).
Confirm that 2020107 connection matches the supply/return pipework and flow direction arrow.
Depressurise the heating circuit, fit the union tailpiece and tighten to factory torque.
Adjust the flow scale (Kvs / l/h) or controller setting according to room or boiler loop load.
Refill the loop, vent trapped air and verify leak-free operation under operating temperature.
Engineer pro tip: When installing Watts (2020107), never wind hemp onto flat gasket seats or Eurocone O-ring cones – seal only tapered pipe threads.
