Loading...
Danfoss · EN 12828Montavimo ir prijungimo mazgo eiga (014G0260):
Gamyklinė komplektacija ir sertifikavimas:
Technical Datasheet & 2D Drawing (014G0260)
Dimensional & hydraulic connection schematic
Sertifikuotas Danfoss gaminys 014G0260 (Danfoss PSU maitinimo šaltinis Danfoss link centriniam valdikliui) iš „Danfoss Link…
In stock · delivery 1–3 bus. days
Material / Spec: Lakštinis plienas S235JR (3–4 mm), išbandytas 1,5×PN hidrauliniu slėgiu
Akumuliacinėms talpoms – juodas plienas; ŠV boileriams – titano emalis + 850 °C degimas.
EN 12828 sauga: tarp boilerio / akumuliacinės talpos ir apsauginio vožtuvo (3 bar šildymui / 6 bar geriamam vandeniui) bei Statico plėtimosi indo draudžiama montuoti uždaromąją armatūrą.
All [01–06] sub-assemblies, adapters, and gaskets stocked at Eigulių St. 21, Kaunas warehouse (10+ yr service support).
Vytautas engineering compatibility note (014G0260)
Verified mating components for Danfoss (014G0260) matched by connection standard (DN / thread / M30×1.5 / RA Click) and hydraulic compatibility.
Yes, this Danfoss unit (SKU 014G0260, category: Boiler room automation & actuators) is manufactured to European EN 12828 hydronic standards. Verify the connection thread or nominal size (e.g. DN15 1/2", DN20 3/4", M30×1.5 or Danfoss RA Click) – our engineering advisor Vytautas lists directly compatible mating components on this page.
Genuine Danfoss components use corrosion-resistant alloys (DZR brass, bronze or stainless steel) and calibrated flow paths, preventing valve sticking, water-hammer noise and premature seal leaks over 10+ heating seasons.
When installing PSU power supply unit for Danfoss Link central controller – 014G0260 (014G0260, retail price 65,88 €), check whether you need matching union tailpieces, Eurocone adapters, a mating thermostatic head or actuator. See the compatible parts section above.
Always observe the flow-direction arrow on the housing, depressurise the loop before fitting, and never apply hemp or tape onto flat union gaskets or O-ring cones.
Danfoss elektroninis valdiklis (PSU maitinimo šaltinis Danfoss link centriniam valdikliui – 014G0260, SKU: 014G0260) skirtas grindinio šildymo kontūrų zoniniam valdymui (maitinimas 230 V / 24 V, pavaros 230 V / 24 V). Tai elektroninis valdymo blokas – neturi M30×1,5 hidraulinio sriegio ar vožtuvo korpuso.
Gamintojo dokumentu patvirtintas suderinamumas (vieno gamintojo sistemos ribose) · Kitiems mazgams: Suderinamumą pasitikslinkite su mūsų inžinieriumi (+370 693 97098) arba pagal įrenginio techninį pasą
Source: Manufacturer technical catalog (Danfoss / IMI Hydronic / HERZ / Haier / Gorenje 2025–2026) and LST EN 215 / EN 12828 / EN 303-5 standard
Verification note: Solid-fuel boiler door aperture and flange dimensions vary by production year and kW rating – before ordering a door conversion kit or pellet burner, verify exact dimensions against the boiler passport or with a „Gilės inžinerija“ engineer (+370 693 97098).
Confirm that 014G0260 connection matches the supply/return pipework and flow direction arrow.
Depressurise the heating circuit, fit the union tailpiece and tighten to factory torque.
Adjust the flow scale (Kvs / l/h) or controller setting according to room or boiler loop load.
Refill the loop, vent trapped air and verify leak-free operation under operating temperature.
Engineer pro tip: When installing Danfoss (014G0260), never wind hemp onto flat gasket seats or Eurocone O-ring cones – seal only tapered pipe threads.
Underfloor heating master controller, 10-zone, supply 230V, supports 12 Danfoss actuators 24V, NC – 088H0017
