Loading...
IMI Heimeier · EN 12828
Technical Datasheet & 2D Drawing (3440-03.000)
Dimensional & hydraulic connection schematic
Calypso DN20, ašinis, be išankstinio nustatymo – 3440-03.000 – IMI Heimeier V-exact II / K-Serija inžinerinis komponentas, skirtas kategorijai „Termostatinės ga
Shipped from central warehouse (delivery 2–4 bus. days)
Material / Spec: Karštai štampuotas žalvaris CW617N / DZR AMETAL-C, PN16, T_max 120 °C
Montuoti tik pagal srauto rodyklę ant korpuso (5×DN prieš vožtuvą, 2×DN už vožtuvo).
Tiesaus vamzdžio taisyklė: ≥ 5×DN prieš balansinį vožtuvą (P1) ir ≥ 2×DN už vožtuvo (P2) stabiliai Δp matavimo charakteristikai.
All [01–06] sub-assemblies, adapters, and gaskets stocked at Eigulių St. 21, Kaunas warehouse (10+ yr service support).
Vytautas engineering compatibility note (3440-03.000)
Verified mating components for IMI Heimeier (3440-03.000) matched by connection standard (DN / thread / M30×1.5 / RA Click) and hydraulic compatibility.
Yes, this IMI Heimeier unit (SKU 3440-03.000, category: Thermostatic heads & valves) is manufactured to European EN 12828 hydronic standards. Verify the connection thread or nominal size (e.g. DN15 1/2", DN20 3/4", M30×1.5 or Danfoss RA Click) – our engineering advisor Vytautas lists directly compatible mating components on this page.
Genuine IMI Heimeier components use corrosion-resistant alloys (DZR brass, bronze or stainless steel) and calibrated flow paths, preventing valve sticking, water-hammer noise and premature seal leaks over 10+ heating seasons.
When installing Calypso DN20, axial, without pre-setting – 3440-03.000 (3440-03.000, retail price 26,21 €), check whether you need matching union tailpieces, Eurocone adapters, a mating thermostatic head or actuator. See the compatible parts section above.
Always observe the flow-direction arrow on the housing, depressurise the loop before fitting, and never apply hemp or tape onto flat union gaskets or O-ring cones.
M30×1,5 standartinis sriegis – tinka IMI Heimeier K / DX / Halo, HERZ M30×1,5 ir elektroninėms M30×1,5 galvutėms (netinka Danfoss RA-Click galvutėms be adapterio). Skirta šoninio pajungimo radiatoriams (DN15 / DN20).
Gamintojo dokumentu patvirtintas suderinamumas (vieno gamintojo sistemos ribose) · Kitiems mazgams: Suderinamumą pasitikslinkite su mūsų inžinieriumi (+370 611 19158) arba pagal įrenginio techninį pasą
Source: Manufacturer technical catalog (Danfoss / IMI Hydronic / HERZ / Haier / Gorenje 2025–2026) and LST EN 215 / EN 12828 / EN 303-5 standard
Verification note: Solid-fuel boiler door aperture and flange dimensions vary by production year and kW rating – before ordering a door conversion kit or pellet burner, verify exact dimensions against the boiler passport or with a „Gilės inžinerija“ engineer (+370 611 19158).
Confirm that 3440-03.000 connection matches the supply/return pipework and flow direction arrow.
Depressurise the heating circuit, fit the union tailpiece and tighten to factory torque.
Adjust the flow scale (Kvs / l/h) or controller setting according to room or boiler loop load.
Refill the loop, vent trapped air and verify leak-free operation under operating temperature.
Engineer pro tip: When installing IMI Heimeier (3440-03.000), never wind hemp onto flat gasket seats or Eurocone O-ring cones – seal only tapered pipe threads.
Automatic thermostatic valve Eclipse, straight, DN15 male thread (G3/4), pre-setting range 10-150 l/h, PN10, nickel-plated – 3936-02.000
